XR2206 Function Signal Generator DIY Kit Sine Triangle Square Wave 1HZ-1MHZ
Features:Voltage Supply: 9-12V DC Input
Waveforms: Square, Sine & Triangle
Impedance: 600 Ohm + 10%
Frequency: 1Hz - 1MHz
SINE WAVE
Amplitude: 0 - 3V at 9V DC input
Distortion: Less than 1% (at 1kHz)
Flatness: +0.05dB 1Hz - 100kHz
SQUARE WAVE
Amplitude: 8V (no load) at 9V DC input
Rise Time: Less than 50ns (at 1kHz)
Fall Time: Less than 30ns (at 1kHz)
Symmetry: Less than 5% (at 1kHz)
TRIANGLE WAVE
Amplitude: 0 - 3V at 9V DC input
Linearity: Less than 1% (up to 100kHz) 10mA
2. The Function Generator component parameter table
Note |
label |
type |
parameters |
R1 |
resistor |
1K |
Regardless of the polarity |
R2 |
Adjustable resistance |
B503=50K |
(by screen printing layer) |
R3, R5,R6 |
resistor |
5.1K |
Regardless of the polarity |
R4 |
resistor |
330 |
Regardless of the polarity |
R7 |
Adjustable resistance |
B503=50K |
(by screen printing layer) |
R8 |
Adjustable resistance |
B104=100K |
(by screen printing layer) |
C1, |
Electrolytic capacitor |
100UF |
The positive short feet negative long feet |
C2 |
non-polar capacitors |
104 |
Regardless of the polarity |
C3,C4 |
Electrolytic capacitor |
10UF |
The positive short feet negative long feet |
C5 |
non-polar capacitors |
105 |
Regardless of the polarity |
C6 |
non-polar capacitors |
473 |
Regardless of the polarity |
C7 |
non-polar capacitors |
222 |
Regardless of the polarity |
C8 |
non-polar capacitors |
101 |
Regardless of the polarity |
U1 |
IC |
XR2206 |
(by screen printing layer) |
JK1 |
DC POWER |
|
(by screen printing layer) |
J1 |
2PIN Jumper cap |
XM2.54 |
Regardless of the polarity |
J2 |
2PIN Jumper cap |
XM2.54 |
Regardless of the polarity |
P1 |
Signal wire terminal |
|
(by screen printing layer) |
J3 |
2*5P Jumper cap |
|
|
3.The welding installation considerations, follow these steps:
1. The components are welding the front board, from low to high principles, namely the first low welding components, such as, capacitor, resistor, diode, etc.
2.Welding IC socket, terminal blocks, finally power socket, adjustable potentiometer.
3.The back with a diagonal cutting pliers to cut short the pins as far as possible
4.Debugging steps:
1.After completion of welding on IC, XR2206, pay attention to the direction of IC, insert the might damage the chip!
2. check the IC whether against, such as anti please timely correction.
3. Insert the power supply, power supply for 5.5 * 2.1 port, inside outside is negative polarity. For 9-12 v power supply voltage. The waveform may not be stable for more than 12 v
5.Using the step:
1. J1 jumper cap plug in, SIN/TRI blue terminals output sine wave (note J1, J2 can only insert one of)|
|2. J2 jumper cap plug in, SIN/TRI blue terminals output triangular wave (note J1, J2 can only insert one of)
3. SQU blue terminals output pulse
4. AMP : Sine wave, triangle wave amplitude adjustment
5. FINE : Frequency fine adjustment
6. Coarse : Frequency of coarse adjustment
6.Schematic diagram of Function Generator
Package Included:
1 x XR2206 Function Signal Generator DIY Kits Sine Triangle Square Output 1HZ-1MHZ
1.We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
2.Orders will be processed instantly and dispatched within 1-2 business days except hoilday, so we do NOT accept any email/message note after you place orders.
3.All package need to wait 30 days ,Please take care it.Less than 30 days,we can't take a refund.
Feedback1.We greatly appreciate your POSITIVE feedback. Please do NOT leave negative feedback without asking for help.
2.Please DON'T leave negative or neutral feedback if you haven't received item in 30 days, because we have mentioned the shipping time repeatedly.
Payment1.We accept PayPal payment ONLY, and must be received within 5 days from the date of purchase.
2. It is easy and safe for you to pay by credit cards, debit cards, bank transfers and PayPal account balances.
3.Buyers are responsible for import duties,custom fees and taxes, if any, please check your country.
Return policy
1.We believe our items are so outstanding. We are convinced you will be happy with your Purchase.
2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund or resend the item to you after the returned item arrived at our warehouse.
3. Please include your eBay ID and item number with any email requests.
Contact us
1. If you have any questions, please feel free to email our service specialists.
2.Just contact us using the " Ask the seller a question" link on eBay.
3.Our aim is to provide Top Level Customer Service, normally so we will try our best to solve any problem.
XR2206 Function Signal Generator DIY Kit Sine Triangle Square Wave 1HZ-1MHZ Features:Voltage Supply: 9-12V DC Input
Waveforms: Square, Sine & Triangle
Impedance: 600 Ohm + 10%
Frequency: 1Hz - 1MHz
SINE WAVE
Amplitude: 0 - 3V at 9V DC input
Distortion: Less than 1% (at 1kHz)
Flatness: +0.05dB 1Hz - 100kHz
SQUARE WAVE
Amplitude: 8V (no load) at 9V DC input
Rise Time: Less than 50ns (at 1kHz)
Fall Time: Less than 30ns (at 1kHz)
Symmetry: Less than 5% (at 1kHz)
TRIANGLE WAVE
Amplitude: 0 - 3V at 9V DC input
Linearity: Less than 1% (up to 100kHz) 10mA
2. The Function Generator component parameter table
Note |
label |
type |
parameters |
R1 |
resistor |
1K |
Regardless of the polarity |
R2 |
Adjustable resistance |
B503=50K |
(by screen printing layer) |
R3, R5,R6 |
resistor |
5.1K |
Regardless of the polarity |
R4 |
resistor |
330 |
Regardless of the polarity |
R7 |
Adjustable resistance |
B503=50K |
(by screen printing layer) |
R8 |
Adjustable resistance |
B104=100K |
(by screen printing layer) |
C1, |
Electrolytic capacitor |
100UF |
The positive short feet negative long feet |
C2 |
non-polar capacitors |
104 |
Regardless of the polarity |
C3,C4 |
Electrolytic capacitor |
10UF |
The positive short feet negative long feet |
C5 |
non-polar capacitors |
105 |
Regardless of the polarity |
C6 |
non-polar capacitors |
473 |
Regardless of the polarity |
C7 |
non-polar capacitors |
222 |
Regardless of the polarity |
C8 |
non-polar capacitors |
101 |
Regardless of the polarity |
U1 |
IC |
XR2206 |
(by screen printing layer) |
JK1 |
DC POWER |
|
(by screen printing layer) |
J1 |
2PIN Jumper cap |
XM2.54 |
Regardless of the polarity |
J2 |
2PIN Jumper cap |
XM2.54 |
Regardless of the polarity |
P1 |
Signal wire terminal |
|
(by screen printing layer) |
J3 |
2*5P Jumper cap |
|
|
3.The welding installation considerations, follow these steps:
1. The components are welding the front board, from low to high principles, namely the first low welding components, such as, capacitor, resistor, diode, etc.
2.Welding IC socket, terminal blocks, finally power socket, adjustable potentiometer.
3.The back with a diagonal cutting pliers to cut short the pins as far as possible
4.Debugging steps:
1.After completion of welding on IC, XR2206, pay attention to the direction of IC, insert the might damage the chip!
2. check the IC whether against, such as anti please timely correction.
3. Insert the power supply, power supply for 5.5 * 2.1 port, inside outside is negative polarity. For 9-12 v power supply voltage. The waveform may not be stable for more than 12 v
5.Using the step:
1. J1 jumper cap plug in, SIN/TRI blue terminals output sine wave (note J1, J2 can only insert one of)|
|2. J2 jumper cap plug in, SIN/TRI blue terminals output triangular wave (note J1, J2 can only insert one of)
3. SQU blue terminals output pulse
4. AMP : Sine wave, triangle wave amplitude adjustment
5. FINE : Frequency fine adjustment
6. Coarse : Frequency of coarse adjustment
6.Schematic diagram of Function Generator
Package Included:
1 x XR2206 Function Signal Generator DIY Kits Sine Triangle Square Output 1HZ-1MHZ
1.We only ship to the confirmed address provided by eBay. please make sure your ebay address is 100% matches the address you would like us to ship to. If not, please let us know before we sent you the package, or we will not be responsible for any loss. hope you could understand.
2.Orders will be processed instantly and dispatched within 1-2 business days except hoilday, so we do NOT accept any email/message note after you place orders.
3.All package need to wait 30 days ,Please take care it.Less than 30 days,we can't take a refund.
Feedback1.We greatly appreciate your POSITIVE feedback. Please do NOT leave negative feedback without asking for help.
2.Please DON'T leave negative or neutral feedback if you haven't received item in 30 days, because we have mentioned the shipping time repeatedly.
Payment1.We accept PayPal payment ONLY, and must be received within 5 days from the date of purchase.
2. It is easy and safe for you to pay by credit cards, debit cards, bank transfers and PayPal account balances.
3.Buyers are responsible for import duties,custom fees and taxes, if any, please check your country.
Return policy
1.We believe our items are so outstanding. We are convinced you will be happy with your Purchase.
2. If you do not satisfy with our items. Please simply return to us within 30 Days in original condition. Just pay for the returned postage. Then we can issue full refund or resend the item to you after the returned item arrived at our warehouse.
3. Please include your eBay ID and item number with any email requests.
Contact us
1. If you have any questions, please feel free to email our service specialists.
2.Just contact us using the " Ask the seller a question" link on eBay.
3.Our aim is to provide Top Level Customer Service, normally so we will try our best to solve any problem.