Lap Steel Guitar 22.5 Scale Conversion RetroFit Kit Nut-Bridge-FretBoard #BSS ED

Vendu Voir des articles similaires EUR 18,47 Achat immédiat, Garantie client eBay
Vendeur: georgeboards ✉️ (1.999) 98.1%, Lieu où se trouve: Belen, New Mexico, US, Lieu de livraison: WORLDWIDE, Numéro de l'objet: 123341019191 Lap Steel Guitar 22.5 Scale Conversion RetroFit Kit Nut-Bridge-FretBoard #BSS ED. Several Import Lap Steel Guitars Sell on eBay under the Brand Names including Rogue Rosetti Artisan.  These lap steel guitars are 21 scale with low quality normal Guitar bridge Saddles and Formed Plastic nuts with normal guitar spacings. GeorgeBoards manufacturing has created a DIY KIT to convert your import lap steel guitar into a playable 22.5" scale with string spacing and height found on Professionally Made Modern Slide Steel Guitars. The Kit includes a 3D Printed Stainless Steel Polymer Composite 1/2" Tall Nut Bridge - 3/8 Nut - .390 Bridge spacings VGrooves for string gauges .056 - .013 and a Black peel n stick 22.5" scale Fretboard pre cut to fit the above mentioned Brands. It takes only an hour or so - hand tools a battery drill - tape measure to quickly convert your new steel guitar into a professional paying and sounding instrument with our RetroFit Kit 1  To make the RetroFit you remove the strings - plastic nut - guitar saddles - plastic fretboard. 2  Remove the Screws and save them from the metal piece under the saddles. 3  Move the metal piece back to the edge of the end of the guitar. Blue Tape it to the edge to hold it in place. 4  Use your tape measure to place the New Nut and Bridge temporarily - use the new fretboard to help place the nut. 5  Make sure the Bridge is in front of the 3  screws at the back of the guitar not on top of them. 6  Blue tape everything for temporary alignment. Tweak all of this until it lays out nicely. 7  Mark where the Bridge hold down holes are going to go through the metal plate and into the wood below. 8  Remove the metal plate and drill holes through it on a separate area so not to drill into the guitar. 9  Return the metal plate and attach it to the guitar with the 3 little screws and 2 or the larger screws in their  original holes except in their new positions.         10 Use 2 of the original larger screws to fill the holes in front of the metal plate. 11 Use your tape measure to place the nut and bridge at 22.5" - Blue tape both. 12 Use #4 X 3/4" Sheet Metal Screws to hold down the Nut and Bridge at 22.5"       Make sure the fretboard fits in front of the metal pickguard plate. Measure multiple times before drilling. 13 Make sure the little ground wire is under the metal plate you moved back. The plate is your string receiver. 14 Fill the holes from the plastic fretboard with chalk - putty  - spackle - whatever. 15 Clean off any debris or oils with rubbing alcohol and peel n stick down the new fretboard. 16 Replace the original strings with new gauged strings for your choice of tuning the VGrooves will fit lighter and heavier gauges.  17 Remember this is an Open E - D tuning  Spacings 3/8 nut - .390 Bridge VGrooves for .056 - .013 gauges or similar. 18 Bring it up to pitch and adjust the pickup height to taste.  
  • Condition: Ouvert (jamais utilisé)
  • Condition: Several Import Lap Steel Guitars Sell on eBay under the Brand Names including Rogue Rosetti Artisan. These lap steel guitars are 21 scale with low quality normal Guitar bridge Saddles and Formed Plastic nuts with normal guitar spacings.GeorgeBoards manufacturing has created a DIY KIT to convert your import lap steel guitar into a playable 22.5" scale with string spacing and height found on Professionally Made Modern Slide Steel Guitars.The Kit includes a Nut Bridge and peel n stick Fretboard pre cut to fit the above mentioned Brands.It takes only an hour or so and hand tools a battery drill - tape measure to quickly convert your new steel guitar into a professional paying and sounding instrument with our RetroFit Kit
  • Parts Included: 1/2 tall Nut - Bridge - Peel N Stick Fretboard
  • String Spacings: Open E-D spacings 3/8 nut - .390 Bridge
  • VGrooves: Set for .056 - .013 or similar gauges
  • Fret Board Color: Black
  • UpGrade your Import Steel to Pro Quality: Kit is Easy to install takes an hour or so
  • Model: 22.5 RetroFit Conversion Kit
  • To Fit: Rogue Rossetti Artisan
  • Country/Region of Manufacture: United States
  • 3D Nut and Bridge Material: Stainless Steel Polymer Composite
  • Brand: GeorgeBoards Manufacturing

PicClick Insights - Lap Steel Guitar 22.5 Scale Conversion RetroFit Kit Nut-Bridge-FretBoard #BSS ED PicClick Exclusif

  •  Popularité - 4 vendu, 0 disponible. 1 personne suit la vente, 0.0 de nouvelles personnes suivent la vente par jour, 39 days for sale on eBay. Nombre normal suivi.
  •  Meilleur Prix -
  •  Vendeur - 1.999+ articles vendu. 1.9% évaluations négative. Grand vendeur avec la très bonne rétroaction positive et plus de 50 cotes.

Les Gens ont Aussi Aimé PicClick Exclusif