Camera Module Board 5MP Webcam Video 1080p 720p for Raspberry Pi 2/3/3B+ Green

Vendu Voir des articles similaires EUR 2,76 Achat immédiat, EUR 1,84 Livraison, Garantie client eBay
Vendeur: xianyeji2016 ✉️ (14.025) 0%, Lieu où se trouve: 深圳市, 广东省, CN, Lieu de livraison: WORLDWIDE, Numéro de l'objet: 132197369907 Camera Module Board 5MP Webcam Video 1080p 720p for Raspberry Pi 2/3/3B+ Green.
Camera Module Board 5MP Webcam Video 1080p 720p for Raspberry Pi 3 Green Description: Connection: Connector location: 90 degrees vertical connector, HDMI port next to that. Connect the contact side toward the HDMI connector Software use: 1. RPi firmware and raspi-config have been updated for the camera, please execute apt-get update; apt-get upgrade; 2. Select the camera in raspi-config, start the camera driver in the RPi firmware, and then reboot 3. Use the command line program raspivid and raspistill to operate the camera, capture video clips or images 4. The captured video clip needs to be played with mplayer How to broadcast the data through the network broadcast broadcast out: Through the nc command (ncat - Concatenate and redirect sockets) will be the camera input data, directly redirect to the network port to achieve output The following is a detailed description parameter: Lens: 1/4 5M Aperture: 2.9 Focal length: 3.29 Field of view angle: 72.4 degrees Hardware connection: 1. Soft cable, 90 degrees vertical connector, HDMI port next to that. Connect the contact side toward the HDMI connector. 2. Remove the protective film on the lens before use 3. Bare board, pay attention to ESD damage, beware of static! Software use: 1. RPi firmware and raspi-config have been updated for the camera, please execute apt-get update; apt-get upgrade; 2. Select the camera in raspi-config, start the camera driver in the RPi firmware, and then reboot 3. Use the command line program raspivid and raspistill to operate the camera, capture video clips or images 4. The captured video clip needs to be played with mplayer How to broadcast the data through the network broadcast broadcast out: Through the nc command (ncat - Concatenate and redirect sockets) will be the camera input data, directly redirect to the network port to achieve output.

How to enable camera support in Raspbian

Boot up the Pi and log in. The default username is pi, and the default password is raspberry. (Note: if you have changed these from the default then you will need to supply your own user/password details).

Run the following commands in a terminal to upgrade the Raspberry Pi firmware to the latest version:

sudo apt-get update

Click to enlarge

sudo apt-get upgrade

Click to enlarge

Access the configuration settings for the Pi by running the following command:

sudo raspi-config

Navigate to camera” and select enable.

Click to enlarge

Click to enlarge

Select Finish” and reboot.

Click to enlarge

How to use the Raspberry Pi camera software

raspivid is a command line application that allows you to capture video with the camera module, while the applicationraspistill allows you to capture images.

-o or output specifies the output filename and -t or timeout specifies the amount of time that the preview will be displayed in milliseconds. Note that this set to 5s by default and that raspistill will capture the final frame of the preview period.

-d or demo runs the demo mode that will cycle through the various image effects that are available.

Example commands

Capture an image in jpeg format:

raspistill -o image.jpg

Capture a 5s video in h264 format:

raspivid -o video.h264

Capture a 10s video:

raspivid -o video.h264 -t 10000

Capture a 10s video in demo mode:

raspivid -o video.h264 -t 10000 -d

To see a list of possible options for running raspivid or raspistill, you can run:

raspivid | less

raspistill | less

Use the arrow keys to scroll and type q to exit.

Extended documentation is available .

Note that we recommend that you change SSH password if you are using a camera, in order to prevent unwanted access.

How to stream video from the Raspberry Pi camera over a network

To view the feed on Linux

Install the dependencies by running the following in a terminal:

sudo apt-get install mplayer netcat

Find your IP address by running ifconfig. (Your IP address will be listed in the console output and will probably be of the form 192.168.1.XXX).

Run the following command in a terminal to view the feed using MPlayer:

nc -l -p 5001 | mplayer -fps 31 -cache 1024 -

To view the feed on Windows

Install and run Linux instead.

Find your IP address by running ipconfig. (Your IP address will be listed in the console output and will probably be of the form 192.168.1.XXX).

Download MPlayer .

Download Netcat .

Note that your browser may complain that these files are malicious, as they are unsigned executables.

Press the Windows key and the r’ key simultaneously to bring up the Run” dialog. Enter cmd.exe into the dialog and press enter/return to open a DOS prompt.

Enter the following command at the prompt to view the feed using MPlayer:

[Path to nc.exe]\nc.exe -L -p 5001 | [Path to mplayer.exe]\mplayer.exe -fps 31 -cache 1024 -

To view the feed on OS X

Download  MPlayer .

Alternatively, you can download mplayer using  Brew , which we recommend.

Find your IP address by running ifconfig. (Your IP address will be listed in the console output and will probably be of the form 192.168.1.XXX).

Run the following command in Terminal to view the feed using MPlayer:

nc -l -p 5001 | mplayer -fps 31 -cache 1024 -

To view the feed on a Raspberry Pi:

Find your IP address by running ifconfig. (Your IP address will be listed in the console output and will probably be of the form 192.168.1.XXX).

Run the following commands in a terminal on the receiving Pi:

mkfifo buffer

nc -p 5001 -l > buffer | /opt/vc/src/hello_pi/hello_video/hello_video.bin buffer

To transmit the feed from the Pi with camera module attached

After setting up the receiving” machine as per the instructions above, run the following commands in a terminal on the transmitting” Pi:

raspivid -t 999999 -o – | nc [insert the IP address of the client] 5001

You can then use the commands listed in the How to use the Raspberry Pi camera software” section above to change the capture time or to add a video effect.

Click to enlarge

How to use the Raspberry Pi camera software

raspivid is a command line application that allows you to capture video with the camera module, while the applicationraspistill allows you to capture images.

-o or –output specifies the output filename and -t or –timeout specifies the amount of time that the preview will be displayed in milliseconds. Note that this set to 5s by default and that raspistill will capture the final frame of the preview period.

-d or –demo runs the demo mode that will cycle through the various image effects that are available.

Example commands

Capture an image in jpeg format:

raspistill -o image.jpg

Capture a 5s video in h264 format:

raspivid -o video.h264

Capture a 10s video:

raspivid -o video.h264 -t 10000

Capture a 10s video in demo mode:

raspivid -o video.h264 -t 10000 -d

To see a list of possible options for running raspivid or raspistill, you can run:

raspivid | less

raspistill | less

Use the arrow keys to scroll and type q to exit.

Extended documentation is available .

Note that we recommend that you change SSH password if you are using a camera, in order to prevent unwanted access.

How to stream video from the Raspberry Pi camera over a network

To view the feed on Linux

Install the dependencies by running the following in a terminal:

sudo apt-get install mplayer netcat

Find your IP address by running ifconfig. (Your IP address will be listed in the console output and will probably be of the form 192.168.1.XXX).

Run the following command in a terminal to view the feed using MPlayer:

nc -l -p 5001 | mplayer -fps 31 -cache 1024 -

To view the feed on Windows

Install and run Linux instead.

Find your IP address by running ipconfig. (Your IP address will be listed in the console output and will probably be of the form 192.168.1.XXX).

Download MPlayer .

Download Netcat .

Note that your browser may complain that these files are malicious, as they are unsigned executables.

Press the Windows key and the ‘r’ key simultaneously to bring up the “Run” dialog. Enter cmd.exe into the dialog and press enter/return to open a DOS prompt.

Enter the following command at the prompt to view the feed using MPlayer:

[Path to nc.exe]\nc.exe -L -p 5001 | [Path to mplayer.exe]\mplayer.exe -fps 31 -cache 1024 -

To view the feed on OS X

Download MPlayer .

Alternatively, you can download mplayer using Brew , which we recommend.

Find your IP address by running ifconfig. (Your IP address will be listed in the console output and will probably be of the form 192.168.1.XXX).

Run the following command in Terminal to view the feed using MPlayer:

nc -l -p 5001 | mplayer -fps 31 -cache 1024 -

To view the feed on a Raspberry Pi:

Find your IP address by running ifconfig. (Your IP address will be listed in the console output and will probably be of the form 192.168.1.XXX).

Run the following commands in a terminal on the receiving Pi:

mkfifo buffer

nc -p 5001 -l > buffer | /opt/vc/src/hello_pi/hello_video/hello_video.bin buffer

To transmit the feed from the Pi with camera module attached

After setting up the “receiving” machine as per the instructions above, run the following commands in a terminal on the “transmitting” Pi:

raspivid -t 999999 -o – | nc [insert the IP address of the client] 5001

You can then use the commands listed in the “How to use the Raspberry Pi camera software” section above to change the capture time or to add a video effect.

Package Included:

1 x Camera Module Board 5MP Webcam Video 1080p 720p for Raspberry Pi 3 Green

Payment Policy:
We ONLY accepted PayPal payment.  shipping & time: Generally, delivery time is   10-20  business days to USA, United Kingdom, Australia  and  15-30  days to most other countries . Items will be shipped within 1 business day on payment received. Delivery time depends on destination and other factors, it may takes up to 30 business days. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility. Returns Policy: All sales come with us 14-day warranty. Return items must not be used or have any sign of abuse or intentional damage. Buyer is responsible for all return shipping charges. We reserve the right not to refund S&H when the item has been posted. Contact us: If you have any questions,Please contact with us via eBay message or our customer service e-mail.  You may expect to receive a response to your inquiry within 24 hours. (Excluding Weekends and Public Holidays) Feedback: Dear buyers, we appreciate your business, if you are satisfied with our service, please leave us a positive feedback . Please email us before leaving any 1 or 2 ratings, negative feedback or open any dispute. We understand the concerns and frustrations you might have, and will do our endeavor to resolve the issues.  Please give us the opportunity to resolve any problem. thank you !
  • Condition: Neuf
  • Non-Domestic Product: No
  • Modified Item: No
  • Country/Region of Manufacture: China
  • Custom Bundle: No
  • Brand: Unbranded/Generic

PicClick Insights - Camera Module Board 5MP Webcam Video 1080p 720p for Raspberry Pi 2/3/3B+ Green PicClick Exclusif

  •  Popularité - 25 personnes suivent la vente, 0.0 de nouvelles personnes suivent la vente par jour, 1.543 days for sale on eBay. Super grande quantité suivi. 459 vendu, 10 disponibles.
  •  Meilleur Prix -
  •  Vendeur - 14.025+ articles vendu. 0% évaluations négative. Bon vendeur avec bonne rétroaction positive et bonne quantité de cotes.

Les Gens ont Aussi Aimé PicClick Exclusif