Specifications
Product Name: High Pressure Perfusion Machine
Rated Power: 720w
Voltage / Flat Rate: 220v Ac / 50hs
Maximum Output Pressure: 10000pai
Start Again: 7500pai
The Maximum Pressure of High Pressure Pipe Is 10000pai
Switching Valve Safety Range:18000pai
Delivery Flow: 0.75 Kg/ Min
High-pressure Perfusion Machine Construction Plan Process:
1.Concrete Building Concrete, Stone Cracks, Cracks, and Pores Are the Main Causes of Damage to Iconcrete Buildings. Leakage of Crack Pores Is the Most Headache Problem, Because the Cracks Inthe Concrete Are Completely Irregular. Generally, the Traditional Method of Plugging Is to Dig Opencracks or Water Leaks to Plug the Surface, but the Result Is Often to Block the Area, Where It Beginsto Leak Again. Because Water Can Move Irregularly in the Internal Cracks of Concrete, It Seeps Fromrelatively Weak Parts.
2.Adopting Chemical Groutingmethod. It Is the Use of Mechanical High-pressure Power(High-pressure Pouring Machine) to Inject Chemical Grouting Materials into Concrete Cracks. Whenthe Slurry Encounters the Water in the Concrete Cracks, It Will Quickly Disperse, Emulsify, Expand,and Solidify. the Depth Is Related to the Width of the Fracture: the Wider the Fracture, the Greaterthe Flow Velocity of the Slurry, the Deeper It Enters the Fracture, and the Better the Grouting Effect.the Initial Swelling Rate of Water-soluble Polyurethane Can Reach 100%. After the Gel Is Formed,the First Swelling Disappears, but It Has Good Elasticity and Becomes a Stable Elastomer Similar Towater-stop Rubber. in This Way, the Consolidated Elastomer Fills All Cracks in the Concrete Andcompletely Blocks the Water Flow Outside the Concrete Structure to Achieve the Purpose Ofstopping Water and Leaks.
3.Cracks Larger than 0.2mm Are Grouted with Water-soluble Polyurethane Slurry; Cracks Smallerthan 0.2mm Are Sealed with Epoxy Resin (for Dry Joints: Sealed with Modified Epoxy Resin Basefluid; for Wet Joints: Water-soluble Polyurethane Grouting May Be Used, and the Modified Epoxy Resin Base Liquid Will Be Used to Seal and Reinforce After Water-stopping and Drying. the Cracksthat Are Dfficult to Grouting Will Be Sealed with . Plug-stopping" to Stop the Water and Thensealed with Modified Epoxy Resin Base Liquid After Drying. ). Note: After Water-basedpolyurethane Grouting, Depending on the Specific Situation, Then Decide Whether to Carry Outmodified Epoxy Resin Grouting.
Advantages of Chemical Grouting Waterproof Plugging Construction:
1.Water-soluble Polyurethane Chemical Grouting Material Is a Low-viscosity, Single-componentsynthetic Polymer Polyurethane Material in the Form of a Slurry, Which Has the Characteristics Ofcross-linking Reaction with Water and Foaming to Form a Multi-layered Closed Elastomer. When Itis Injected with High Pressure into the Concrete Crack Structure and Extends Until All the Gaps Arefilled (Including 0.015mm Micro-slits That Are Invisible to the Naked Eye), When It Encounterswater (Water Injection), a Large Amount of Carbon Dioxide Gas Is Released Along with Thecross-linking Reaction, Resulting in Secondary Osmotic Pressure. High-pressure Thrust Andsecondary Osmotic Pressure Again Press the Elastomer into and Fill All the Gaps to Achieve Thepurpose of Stopping Leakage.
Construction Technology of Waterproofing and Plugging by Chemical Grouting
High-pressure Chemical Grouting Plugging Construction Should Be Carried out by a Professionallytrained Construction Team with Professional Construction Equipment.
1. Cleaning: Check and Analyze the Leakage Situation in Detail, and Determine the Position Andspacing of the Grouting Holes. Clean up the Area That Needs to Be Constructed, and Remove Theprecipitates on the Concrete Surface to Ensure That the Surface Is Clean.
2. Drilling: Use a Dilling Tool to Drill Pressure Relief Holes Around the Hole. the Diameter of Thedrill Bit Is 14mm. the Dilling Angle Should Be = 45 " . the Dilling Depth 2/3 of Thestructural Thickness. the Dilling Must Obliquely Pass Through the Main Leakage Hole. However, Itis Not Allowed to Penetrate the Structure, Because the Dust in the Larger Holes of the Movingwater Will Be Washed Away by Itself. the Slow Penetration of the Wall Surface Is to Drill Plumblossom Holes on the Seepage Surface. Rinse the Grouting Hole with a Washing Machine Until Thegrouting Hole Is Clear, Then You Can Proceed to the Next Step.
3. Buried Mouth: Observe the Pressure of the Main Leak Hole. When the Water Flow Is Not Urgentand the Pressure Is Not Large, the Quick-drying Plugging Agent Can Be Used to Bury the Groutingwater-stopping Needle. After the Structure Is Stable, Re-drill the Wooden Wedge and Install Theexpansion Water Stop Needle). When the Structure Reaches a Certain Strength and There Is Noleakage, the Other Drain Holes Are Respectively Installed with Expansion Water Stop Needles, Andtightened with a Special Allen Wrench, so That There Is No Gap Between the Groutin
PaiementDétails de livraisonpolitique de retourréactionContactez nousPaiementDélai de livraison:
1-5 jours ouvrables pour | France |
6-10jours ouvrables pour | Irlande, Autriche, Belgique, Danemark, Finlande, Portugal, Suède, Espagne, Grèce,etc |
réaction
Nous maintenons des niveaux élevés d'excellence et essayons d'obtenir la satisfaction cent pour cent du client. La rétroaction est très importante pour nous. Nous espérons que vous nous contactez juste avant que vous donniez la rétroaction neutre ou négative, de sorte que nous pouvions répondre à vos préoccupations. Il est impossible de résoudre les problèmes si nous ne savons rien sur elles!
Contactez nousHerstellernummer | Nicht zutreffend |
---|---|
Marke | Markenlos |
Rated power | 720W |
Voltage / Flat Rate | 220v AC / 50Hs |
Maximum output pressure | 10000pai |
Start again | 7500pai |
Switching valve safety range | 18000pai |
Delivery flow | 0.75 kg/ min |
Marque | - Sans marque/Générique - |
Numéro de pièce fabricant | Non applicable |