Parcel include:
1 x 3 Axis DIY Mini 3018 Pro GRBL Control CNC Engraver Milling machine kit
1 x ER11 Collet
1 x 775 spindle
1 x GRBL control board
1 x Offline hand controller
1 x Power Supply
10 x 20° 0.1mm drill bits
4 x plates
1 x Set of allen wrench
1 x 4G U disk include user manual and grbl software
Descriptions:
working area |
30x18x4.5cm |
Frame size |
33x40x24cm |
Mesa |
30x18cm |
Spindle |
775 spindle motor (12-36V) 24V: 10000r/min
|
Spindle Chuck |
ER11 |
Step motor |
Fuselage length 34MM,Current 1.33A, 12v.Torque 0.25N/M |
Power supply |
24V 5.6A |
Software |
GRBL controller |
supported system |
windows XP SP3, win7, win8, win10(32/64 can be)(Do not support Mac)
|
Drill bits |
tip 0.1mm ,20 degree , diameter3.175mm.the package include 10pc |
Laser |
Support laser |
clamps |
4 pcs, Hold the thickness of 0-30mm,size: 50 * 20 * 3 (length * width * thick), the inner slot width 6mm |
Introduction:
Body used profiles and plastic, small size, light weight, USB interface, GRBL control system, learning, entry preferred. Can use carving knife, but also can use laser engraving.
Can be engraved plastic, wood, acrylic, pvc, pcb, wood and the other similar material.
Specification:
Main application:
Can be engraved plastic, wood, acrylic, pvc, pcb, wood and the other similar material.
GRBL Control Board
GRBL 1.1F USB port cnc engraving machine control board, 3 axis control
Specification:
Connection: USB (USB-CH340)
Software: GRBL controller, UniversalGcodeSender
Input voltage: 24VDC (12-24VDC)
Stepper motor: support 24V 2A
Spindle motor: support 24V 10A (supports PWM0%-100%)
Master chip: atmel 328P (arduino nano)
Spindle drive chip: MOSFET (recommendation 12~36V, current : within 10A )
Spindle PWM speed: Support
Support stepper motor: 12V, maximum current of 2A or less is recommended within 1.5A and additional heat. (Any stepper motor 42, 57)
Laser engraving: Support
Power Interface: 5.5-2.5mm DC interface
Support system: win-xp,win7,win8,win10
Advantage
add the outer casing: mainly for the bare board of the control board, short circuit problem during use add the power button switch (this switch is the power supply control signal, there is no large current passing through the switch, do not worry about the switch size) Cancel the drive module, integrated imported stepper motor drive, with short circuit protection, no need to worry about module damage. And integrated heat dissipation aluminum alloy add the fan to force heat dissipation. add offline recognition to insert offline modules and computers at the same time. Offline will automatically identify if there is computer control. Enhanced spindle drive. Can support 20,000 rpm spindle. Support for larger power spindles
SD shows it is SD card condition, turn on power supply after insert SD card, otherwise, it won't work. SD card capacity 4G could be recognized.
Press X- or X+ button to switch
Control:Press confirmation button to access manually controlling page
File:Press confirmation button to access file page
Set:Press confirmation button to access setting page
On the off-line controller, buttons control corresponding actions.
SPN is spindle controlling,should press SPIN.
Fan is fan controlling, should press SMOD.
Note: To exit this page, should press back button longly. after exit, save the current location as engraving starting point X0Y0Z0
Note: system can recognize max 100 available files one time (***.TXT***.txt***. NC***.nc***.CNC
***.cnc***.TAP***.tap could be recognized),not support files with long name.
Press Y+ or Y- to choose files need to be engraved, press confirmation button to access engraving page.
Press ok to start engraving
If you want to stop during engraving, press back button longly, then back to the file selection page(machine will not stop at once, as GRBL controller has already saved a part of G code, will stop after carry out completely).
The left words show the machine moving distances every time you press the button on the condition of manually controlling, press Y+ or Y- to choose, default 1mm each time.
Press X- or X+ for switchover setting.
The right words show Communication baud rate setting, default 9600
After setting, press confirmation button to save, then press back button to exit setting page.
Note: the setting parameters can not be saved on the condition of electricity outage, it will be default value when turn on next time.
We care about our valued customers,and will always try to help you,hope to establish long business with you.
Pls give us the opportunity to resolve any problem, we understand the concerns and frustrations you might have,and will try our best to resolve the issues.
Pls contact us by ebay message or email before leaving any negative feedback or opening any cases on the site,we will help you to resolve the problem