1 x 3 018 Pro Max GRBL CNC Laser machine kit (without laser) with ER11 collet

1 x GRBL 1.1f Control Board

1 x Offline Remote Control

10 x 20°0.1mm drill bits

4 x Plates

1 x Set of allen wrench

1 x Power Supply

1 x 4G U Disk include user manual & grbl software

                   100% Brand New and High Quality!

product parameters

 

working area	30x18x4.5cm
Frame size	42x35x27cm
Mesa	30x18cm
Spindle	775 spindle motor (12-36V) 24V: 10000r/min
Spindle Chuck	ER11
Step motor	Fuselage length 34MM,Current 1.33A, 12v.Torque 0.25N/M
Power supply	24V 5.6A
Software	GRBL controller
supported system	windows XP SP3, win7, win8, win10(32/64 can be)(Do not support Mac)
Drill bits	tip 0.1mm ,20 degree , diameter3.175mm.the package include 10pc
Laser	Support laser
clamps	4 pcs, Hold the thickness of 0-30mm,size: 50 * 20 * 3 (length * width * thick), the inner slot width 6mm

 

Main application:

  Can be engraved plastic, wood, acrylic, pvc, pcb, wood and the other similar material.

        Offline Controller:  1 Inch LCD, gcode, txt, faucet, nc, ncc, cnc and other processing file    formats, with instructions in English and 1GB micro SD card (with TF card)  

Using with 775 spindle motor (cutters):

Design software: CAM

Control software: GRBL (GRBLcontrol / Candela)

File format: G code (gcode / txt / nc / ncc / tap / ...)

Spindle power: 120W (24V)

Spindle speed: 10000rpm

Processing method: relief / drilling / cutting

Workable material: wood / plastic / PCB / acrylic / plywood / ...

GRBL 1.1F USB port cnc engraving machine control board, 3 axis control

Specification:

Connection: USB (USB-CH340)

Software: GRBL controller, UniversalGcodeSender 

Input voltage: 24VDC (12-24VDC)

Stepper motor: support 24V 2A

Spindle motor: support 24V 10A (supports PWM0%-100%)

Master chip: atmel 328P (arduino nano)

Spindle drive chip: MOSFET (recommendation 12~36V, current : within 10A )

Spindle PWM speed: Support

Support stepper motor: 12V, maximum current of 2A or less is recommended within 1.5A and additional heat. (Any stepper motor 42, 57)

Laser engraving: Support

Power Interface: 5.5-2.5mm DC interface

Support system: win-xp,win7,win8,win10

 

Advantage

add the outer casing: mainly for the bare board of the control board, short circuit problem during use add the power button switch (this switch is the power supply control signal, there is no large current passing through the switch, do not worry about the switch size) Cancel the drive module, integrated imported stepper motor drive, with short circuit protection, no need to worry about module damage. And integrated heat dissipation aluminum alloy add the fan to force heat dissipation. add offline recognition to insert offline modules and computers at the same time. Offline will automatically identify if there is computer control. Enhanced spindle drive. Can support 20,000 rpm spindle. Support for larger power spindles

 

     

GRBL controller Function:

 

 

 

 

SD shows it is SD card condition, turn on power supply after insert SD card, otherwise, it won't work. SD card capacity 4G could be recognized. 

Press X- or X+ button to switch

Control：Press confirmation button to access manually controlling page

File：Press confirmation button to access file page

Set：Press confirmation button to access setting page

 

 

On the off-line controller, buttons control corresponding actions.

SPN is spindle controlling,should press SPIN. 

Fan is fan controlling, should press SMOD.

Note: To exit this page, should press back button longly. after exit, save the current location as engraving starting point X0Y0Z0

 

 

Note: system can recognize max 100 available files one time (***.TXT***.txt***. NC***.nc***.CNC

***.cnc***.TAP***.tap could be recognized)，not support files with long name.

Press Y+ or Y- to choose files need to be engraved, press confirmation button to access engraving page.

Press ok to start engraving

If you want to stop during engraving, press back button longly, then back to the file selection page（machine will not stop at once, as GRBL controller has already saved a part of G code, will stop after carry out completely).

 

The left words show the machine moving distances every time you press the button on the condition of manually controlling, press Y+ or Y- to choose, default 1mm each time.

Press X- or X+ for switchover setting.

The right words show Communication baud rate setting, default 9600

After setting, press confirmation button to save, then press back button to exit setting page.

Note: the setting parameters can not be saved on the condition of electricity outage, it will be default value when turn on next time.

Payment: > 1. Payment is needed to receive within 5 days after deal. > 2. We only accept PayPal. > 3. PayPal is the only online payment method we accept. Please make sure you have a valid/confirmed PayPal account prior bidding. And please make sure that your PayPal registed address is the same with your eBay registed address.  Feedback: We maintain hightest buyer ratings > Positive Feedback will be much appreciated from you. > Any dissatisfaction,please contact us immediately! > Please do not leave neutral or negative feedback before we help you out. Returns: > Defect: We will fully refund or send you a new replacement,please contact and return within 30 days. > Dissatisfaction: Please contact within 3 days, we will fully refund, after got your returned goods. > Missing parts/Q'ty: Please contact us immediately,for a new package arranged,or a partial refund issued. Contact us: > If have any question, Please contact us by ebay message before leaving neutral, negative feedback or open any dispute, we will reply within 24hours, ensure that help you solve the problem, make you satisfied.

• Condition: Neuf
• Objet modifié: Non
• Marque: RATTM MOTOR
• Support System: Windows XP / Win 7 / Win 8 / Win 10
• Working area :: 30x18x4.5cm
• Stepper Motor: Nema17 Stepper,Torque 0.3N/M, 1.3A
• Laser: Support laser
• Control Board: GRBL 1.1F V3.4 GRBL Control Board
• Offre groupée personnalisée: Non
• Software: GRBL controller
• Frame size: 42x25x27CM
• spindle: 775 spindle motor (12-36V) 24V: 10000r/min

Voir Plus